Display[0]
contains a pointer to the most recent activation record for lex level
zero, Display[1] contains a pointer to the most recent activation
record for lex level one, and so on. Assuming you've maintained the Display
array in the current data segment (always a good place to keep it) it only
takes two instructions to access any non-local variable. Pictorially, the
display works as shown below:Note that the entries in the display always point at the most recent
activation record for a procedure at the given lex level. If there is no
active activation record for a particular lex level (e.g., lex level six
above), then the entry in the display contains garbage.
The maximum lexical nesting level in your program determines how many elements
there must be in the display. Most programs have only three or four nested
procedures (if that many) so the display is usually quite small. Generally,
you will rarely require more than 10 or so elements in the display.
Another advantage to using a display is that each individual procedure can
maintain the display information itself, the caller need not get involved.
When using static links the calling code has to compute and pass the appropriate
static link to a procedure. Not only is this slow, but the code to do this
must appear before every call. If your program uses a display, the callee,
rather than the caller, maintains the display so you only need one copy
of the code per procedure. Furthermore, as the next example shows, the code
to handle the display is short and fast.
Maintaining the display is very easy. Upon initial entry into a procedure
you must first save the contents of the display array at the current lex
level and then store the pointer to the current activation record into that
same spot. Accessing a non-local variable requires only two instructions,
one to load an element of the display into a register and a second to access
the variable. The following code implements the Outer, Middle,
and Inner procedures from the static link examples.
; Assume Outer is at lex level 1, Middle is at lex level 2, and
; Inner is at lex level 3. Keep in mind that each entry in the
; display is two bytes. Presumably, the variable Display is defined
; in the data segment.
Outer proc near
push bp
mov bp, sp
push Display[2] ;Save current Display Entry
sub sp, 2 ;Make room for I.
mov word ptr [bp-4],1 ;Set I to one.
call Middle
add sp, 2 ;Remove local variables
pop Display[2] ;Restore previous value.
pop bp
ret
Outer endp
Middle proc near
push bp ;Save dynamic link.
mov bp, sp ;Set up our activation record.
push Display[4] ;Save old Display value.
sub sp, 2 ;Make room for J.
mov word ptr [bp-2],2 ;J := 2;
mov bx, Display[2] ;Get static link to prev LL.
mov ax, ss:[bx-4] ;Get I's value.
add ax, [bp-2] ;Add to J and then
puti ; print the sum.
putcr
call Inner
add sp, 2 ;Remnove local variable.
pop Display[4] ;Restore old Display value.
pop bp
ret
Middle endp
Inner proc near
push bp ;Save dynamic link
mov bp, sp ;Set up activation record.
push Display[6] ;Save old display value
sub sp, 2 ;Make room for K.
mov word ptr [bp-2],2 ;K := 3;
mov bx, Display[4] ;Get static link to prev LL.
mov ax, ss:[bx-4] ;Get J's value.
add ax, [bp-2] ;Add to K
mov bx, Display[2] ;Get ptr to Outer's Act Rec.
add ax, ss:[bx-4] ;Add in I's value and then
puti ; print the sum.
putcr
add sp, 2
pop Display [6]
pop bp
ret
Inner endp
Although this code doesn't look particularly better than the former code,
using a display is often much more efficient than using static links.leave instruction is very simple to understand. It performs
the same operation as the two instructions: mov sp, bp
pop bp
Therefore, you may use the instruction for the standard procedure exit code
if you have an 80286 or later microprocessor. On an 80386 or earlier processor,
the leave instruction is shorter and faster than the equivalent
move and pop sequence. However, the leave instruction is slower
on 80486 and later processors.enter instruction takes two operands. The first is the
number of bytes of local storage the current procedure requires, the second
is the lex level of the current procedure. The enter instruction
does the following:; ENTER Locals, LexLevel
push bp ;Save dynamic link.
mov tempreg, sp ;Save for later.
cmp LexLevel, 0 ;Done if this is lex level zero.
je Lex0
lp: dec LexLevel
jz Done ;Quit if at last lex level.
sub bp, 2 ;Index into display in prev act rec
push [bp] ; and push each element there.
jmp lp ;Repeat for each entry.
Done: push tempreg ;Add entry for current lex level.
Lex0: mov bp, tempreg ;Ptr to current act rec.
sub sp, Locals ;Allocate local storage
As you can see from this code, the enter instruction copies
the display from activation record to activation record. This can get quite
expensive if you nest the procedures to any depth. Most HLLs, if they use
the enter instruction at all, always specify a nesting level
of zero to avoid copying the display throughout the stack.BP-(n*2). The enter instruction does not copy
the value for display[0] into each stack frame. Intel assumes that you will
keep the main program's global variables in the data segment. To save time
and memory, they do not bother copying the display[0] entry.; enter n, 0 ;14 cycles on the 486
push bp ;1 cycle on the 486
sub sp, n ;1 cycle on the 486
; enter n, 1 ;17 cycles on the 486
push bp ;1 cycle on the 486
push [bp-2] ;4 cycles on the 486
mov bp, sp ;1 cycle on the 486
add bp, 2 ;1 cycle on the 486
sub sp, n ;1 cycle on the 486
; enter n, 2 ;20 cycles on the 486
push bp ;1 cycle on the 486
push [bp-2] ;4 cycles on the 486
push [bp-4] ;4 cycles on the 486
mov bp, sp ;1 cycle on the 486
add bp, 4 ;1 cycle on the 486
sub sp, n ;1 cycle on the 486
; enter n, 3 ;23 cycles on the 486
push bp ;1 cycle on the 486
push [bp-2] ;4 cycles on the 486
push [bp-4] ;4 cycles on the 486
push [bp-6] ;4 cycles on the 486
mov bp, sp ;1 cycle on the 486
add bp, 6 ;1 cycle on the 486
sub sp, n ;1 cycle on the 486
; enter n, 4 ;26 cycles on the 486
push bp ;1 cycle on the 486
push [bp-2] ;4 cycles on the 486
push [bp-4] ;4 cycles on the 486
push [bp-6] ;4 cycles on the 486
push [bp-8] ;4 cycles on the 486
mov bp, sp ;1 cycle on the 486
add bp, 8 ;1 cycle on the 486
sub sp, n ;1 cycle on the 486
; etc.
If you are willing to believe Intel's cycle timings, you can see that the
enter instruction is almost never faster than a straight line
sequence of instructions that accomplish the same thing. If you are interested
in saving space rather than writing fast code, the enter instruction
is generally a better alternative. The same is generally true for the leave
instruction as well. It is only one byte long, but it is slower than the
corresponding mov bp,sp and pop bp instructions.enter
appears in the exercises.